All Category

Flow Filteration

Flow filtration means that filtration is performed while suppressing the adhesion of impurities to the membrane surface by flowing the supply liquid parallel to the filtration surface. In general full-scale filtration equipment, the flow of the supply liquid and the filtrate is the same, so the flow is poor and particles adhere to the membrane surface. Compared to this, flow filtration reduces the amount of adhered substances on the membrane surface and increases the filtration speed. It is also convenient because it can be easily washed and used repeatedly. It is suitable mainly for concentration of large samples and buffer exchange.

Other Related Pages

View : Grid List
Filter

13 Item(s)

Set Ascending Direction
  1. Cross Flow Filtration (Vivaflow 50 Flip-Flow Filtration)
    Sartorius Japan Cross Flow Filtration (Vivaflow 50 Flip-Flow Filtration)
    Since it circulates in a narrow flow path by flip flow, high-speed cross flow is possible even with a small pump capacity. Within 50 minutes, 500 mL can be concentrated to 15 mL or less. Most can be recovered with a single rinse of 10 mL. * MWCO represents the molecular weight cut-off.
    Dimension (mm)  107×84×25  Flow Rate (mL/min)  200~400  Effective filtration area (cm2 50  Maximum Operating Temperature (℃)  60℃  Minimum Circulation Volume (mL)  less than 10 
    from S$389.90
    Min. 13 days
  2. Crossflow Filtration Cassette (Vivaflow 200)
    AS ONE Crossflow Filtration Cassette (Vivaflow 200)
    Economical because it is easy to clean and can be used repeatedly. A large-capacity filtration system that uses a cross-flow system. Concentration from 250 mL to 20 mL or less can be done in a few minutes, and 1 L 50 times concentration can be done within 30 minutes. By using two units in paralle... Read More
    Flow Rate (mL/min)  (Pump) 200-400  Dimension (mm)  126×138×38  Minimum Circulation Volume (mL)  20 or less  Effective filtration area (cm2 200  Maximum Operating Temperature (℃)  45℃  Residual liquid volume (mL)  5.3 
    from S$1,099.00
    Min. 13 days
  3. Vivaflow 200 PES
    Sartorius Japan Vivaflow 200 PES
    A large amount of sample (about 0.1 to 5 L) can be concentrated in a short time. The original flip flow method reproduces a high flow rate even with a high concentration solution. It is disposable price and can be washed and reused (50R.200 type). Circulating concentration and solvent replacement... Read More
    Material (Filter)  PES 
    from S$1,099.00
    Min. 4 days
  4. Vivaflow 200 Hydrosart
    Sartorius Japan Vivaflow 200 Hydrosart
    A large amount of sample (about 0.1 to 5 L) can be concentrated in a short time. The original flip flow method reproduces a high flow rate even with a high concentration solution. It is disposable price and can be washed and reused (50R.200 type). Circulating concentration and solvent replacement... Read More
    Material (Filter)  Hydrosart®; 
    from S$1,099.00
    Min. 4 days
  5. Vivaflow 50 PES
    Sartorius Japan Vivaflow 50 PES
    A large amount of sample (about 0.1 to 5 L) can be concentrated in a short time. The original flip flow method reproduces a high flow rate even with a high concentration solution. It is disposable price and can be washed and reused (50R.200 type). Circulating concentration and solvent replacement... Read More
    Molecular weight cut off  MWCO/3,000  Material (Filter)  PES 
    from S$389.90
    Min. 4 days
  6. Viva Flow 50 Hydro
    Sartorius Japan Viva Flow 50 Hydro
    A large amount of sample (about 0.1 to 5 L) can be concentrated in a short time. The original flip flow method reproduces a high flow rate even with a high concentration solution. It is disposable price and can be washed and reused (50R.200 type). Circulating concentration and solvent replacement... Read More
    Material (film)  Hydrosart®;  Type  Viva Flow 50R 
    from S$649.90
    Min. 4 days
  7. Ultra filter
    ADVANTEC Ultra filter
    from S$329.90
    Min. 7 days
  8. Resin molded depth filter cartridge Micro Clean MK Series
    3M Resin molded depth filter cartridge Micro Clean MK Series
    A deep filtration type filter cartridge with a hard structure and a density gradient. It is also suitable for filtering highly viscous solutions. Industrial water, paints, inks, various industrial oils, etc.
    Recommended replacement differential pressure (MPa)  0.14~0.21  Inner Dia. x Outer Dia. (Φmm)  26×66  Mass (g)  150  Length (mm)  248  Suitable for  1BS1・5DCN1  Maximum Operating Temperature (℃)  120 
    Discontinued
  9. Injection molding microchip (evaluation type) kit
    AS ONE Injection molding microchip (evaluation type) kit
    Has excellent hydrophilicity, transparency, and heat resistance. Microscopic observation with transmitted light is also possible. The water injected into the groove of the tip flows through the groove at a constant speed. It can be used for evaluation in development experiments. Suitable for geno... Read More
    Set Contents  2 chips, 5 connectors, 1 tube (30 cm)  As ONE Part Number  2-8234-09 
    Discontinued
  10. CUNO Safety filter system for circulating oil
    3M CUNO Safety filter system for circulating oil
    A pre-selected package of stainless steel housing and resin molded depth filter cartridge. Removes fine particles that are difficult to see visually. Circulation filtration of industrial oil. Removal of foreign matter in cooling oil and lubricating oil. * Since this product is not intended for ge... Read More
    Trusco Part No.  384-8281  Outer Dia. x Height H (Φmm x mm)  93×341  Connector Diameter  Rc1/2(15A) 
    Discontinued
  11. Electroosmotic pump (microchip drive)
    AS ONE Electroosmotic pump (microchip drive)
    * When DC24V is applied
    Dimension (mm)  Φ6 × 11.5 (including reservoir) 
    Discontinued
  12. CUNO Foreign matter removal of cutting fluid Filter system
    3M CUNO Foreign matter removal of cutting fluid Filter system
    A pre-selected package of stainless steel housing and filter cartridge. This is the most typical filter selection. Change the filtration grade of the filter according to your purpose. Filtration of cutting fluid. Removal of abrasive powder, metal scraps, carbon powder, etc. * Since this product i... Read More
    Connection Size (inch)  PT2  Outer Dia. x Height H (Φmm x mm)  201×565~750  Trusco Part No.  384-8272 
    Discontinued
  13. Injection molding microchip (evaluation type)
    AS ONE Injection molding microchip (evaluation type)
    Has excellent hydrophilicity, transparency, and heat resistance. Microscopic observation with transmitted light is also possible. The water injected into the groove of the tip flows through the groove at a constant speed. It can be used for evaluation in development experiments. Suitable for geno... Read More
    Discontinued
View : Grid List
Filter

13 Item(s)

Set Ascending Direction