End Cutting Pliers

Cut the head of screws, nails, etc.

A must-have for plastering work! Scrape off at the optimum blade angle for joint removal

Ideal for harsh use. It is often used by professional craftsmen. It has extremely high wear resistance and is designed to have an excellent weight balance. The hardness of the blade that has been carefully hardened is approximately HRC60. The material is special tool steel that has been oil-quenc... Read More

A must-have for plastering work! A tile cutter that inserts a marking line on the marking needle side and folds the tile on the U-shaped side.

A must-have for plastering work! For cutting tiles on walls and floors! Easy and speedy cutting of tile-cutting tiles Side bitter type, with carbide tip

The distance between the blade and the fulcrum is short, so cutting is possible easily. For cutting nails protruding on the wall surface. For cutting work

It is a reasonable cutting tool that is ideal for twisting and cutting wires. Due to its unrivaled precision and long tool life, it is used all over the world. The hardness of the blade that has been carefully hardened is approximately HRC61. The material is special tool steel that has been oil-q... Read More

The long handle and small head make it easy to apply force.

Make a streak in the tile with a tile cutter.

For cutting slate, gypsum board, decora, fireproof board, plastic, non-combustible decorative board, etc. You can cut by inserting a cut line to the depth of about one-third on the surface of the cut object and bending it.

The tile cutting A type and B type have the same shape, but there is a difference between the one with cemented carbide and the one with high shaving. For porcelain tiles, it is also suitable to have a strong cemented carbide. The cutting edge of the tile-cutting C type is slightly smaller than t... Read More

The distance between the blade and the fulcrum is short, so cutting is possible easily. For cutting nails protruding on the wall surface. For cutting work

For cutting nails, etc. For cutting work

It is a reasonable cutting tool that is ideal for twisting and cutting wires. The very slim shape makes it easy to twist deep wires. Due to the principle of efficient leverage, it demonstrates high cutting ability with less force. Since the wire can be cut with a small stroke, there is no burden.... Read More

A must-have for plastering work! For cutting tiles on walls and floors! You can also cut glass! Easy and speedy cutting of tiles Similar to roller type glass cutting, the tile nippers that can be injured with a roller blade and folded by pinching are safe and convenient. Can cut up to 7 mm thick ... Read More

For cutting nails and soft / steel wires. With biting cutting, there are few uncut parts.

You can twist and cut the binding wire from the roll with a single operation. The hardened cutting blade has a hardness of about 61 HRC.

A must-have for plastering work! For cutting tiles on walls and floors! Easy and speedy cutting of tiles Convenient shape for hole shape and curved cutting Blade width: Approximately 6 mm, with carbide tip

It has the cutting edge of the R blade, and it is easy to apply force to the center, so the cutting force is improved.

It can be used for tile joints, etc.

For cutting nails, etc. For cutting work

With the cutting edge of the R blade, you can perform detailed work such as circular cutting and chipping.

For cutting slate, gypsum board, decora, fireproof board, plastic, non-combustible decorative board, etc. You can cut by inserting a cut line to the depth of about one-third on the surface of the cut object and bending it.

Since the base of the blade of the X nipper is on one side, it is possible to cut like biting. The XN-11 has a roller blade on the side and can also cut glass tiles.

Compared to a general eating cut of the same size, the force applied can be reduced by 25%. The high lever ratio joint makes it easy to work with thick binding wires. You can twist and cut the binding wire from the roll with a single operation. The hardened cutting blade has a hardness of about 6... Read More

It has a straight blade and an R blade, and it is easy to apply force to the center, so the cutting force is improved. Suitable for straight cutting.

It has the cutting edge of the R blade, and it is easy to apply force to the center, so the cutting force is improved.

Since the base of the blade is on one side, it is possible to cut as if it bites into it.

There are few uncut parts due to biting cutting.

The eccentric design allows it to be handled with a light force. The handle is long and can reach far.

The distance from the fulcrum to the blade is very short, making it easy to cut. For cutting nails and wires. * Please note that hard wires such as high-hardness wire and piano wire will damage the blade.

The distance from the fulcrum to the blade is very short, making it easy to cut. For cutting nails and wires. * Please note that hard wires such as high-hardness wire and piano wire will damage the blade.

Beeha's Classic series offers a wide range of products that meet basic performance at a reasonable price. The handle is covered with vinyl that fits comfortably in your hand.